Fundamentals of Industrial Oil Hydraulics and Pneumatics (USB)

Media Storage Type : 32 GB USB Stick

NPTEL Subject Matter Expert : Prof. R.N. Maiti

NPTEL Co-ordinating Institute : IIT Kharagpur

NPTEL Lecture Count : 43

NPTEL Course Size : 13 GB

NPTEL PDF Text Transcription : Available and Included

NPTEL Subtitle Transcription : Available and Included (SRT)

Lecture Titles:

Lecture 1 - What is Hydraulic and Pneumatic System
Lecture 2 - Basic Components, Symbols and Circuits
Lecture 3 - Incompressible Fluids - Some Fundamental Properties
Lecture 4 - Incompressible Fluid Flow related to Fluid Drive
Lecture 5 - Capillary Fluid (incompressible) Flow and Hydrodynamic Lubrication
Lecture 6 - Basis for Calculating Hydraulic Systems
Lecture 7 - Different types of Valves - Features and Operations - I
Lecture 8 - Hydraulic Valves (General) Different types of Valves - Features and Operations - II
Lecture 9 - Hydraulic Circuits and Valves
Lecture 10 - Hydraulic Servomechanism and Servo and Proportional Control Valves
Lecture 11 - Basic Spool Valve Design Analysis
Lecture 12 - General Control Valve Analysis
Lecture 13 - Critical Centre Spool Valve Analysis
Lecture 14 - Critical Centre Spool Valve Analysis - Stroking Forces
Lecture 15 - Proportional Solenoid Pilot Operated Two Stage Pressure Relief Valve
Lecture 16 - Proportional Solenoid Pilot Operated Two Stage Pressure Relief Valve (Continued...)
Lecture 17 - Introduction to Positive Displacement Hydrostatic Units (Hydraulic Pumps and Motors)
Lecture 18 - Basic features of some Hydraulic Pumps and Motors
Lecture 19 - Analysis of an axial - Piston Swash Plate type Hydrostatic Pump (Discharge Flow Characteristics)
Lecture 20 - Analysis of an axial - Piston Swash Plate type Hydrostatic Pump (Estimation of Torque on Drive Shaft and Swash Plate)
Lecture 21 - Analysis of an Axial - Piston Swash Plate type Hydrostatic unit (Pressure Ripple and Swash Plate Torque)
Lecture 22 - Design Analysis of Gear Pumps - I
Lecture 23 - Design Analysis of Gear Pumps - II
Lecture 24 - Basic Concept of Hydrostatic Transmission (HST) System
Lecture 25 - Selection of HST units and components
Lecture 26 - Regenerative Circuits
Lecture 27 - Introduction to Fluid Logic
Lecture 28 - Basic Devices, Symbols and Circuits
Lecture 29 - Logic Circuits
Lecture 30 - Design Analysis of ORBIT Motor - I : Basic Design and Feature
Lecture 31 - Design Analysis of ORBIT Motor - II : Geometric Volume Displacement
Lecture 32 - Design Analysis of ORBIT Motor - III : Output torque and stress, Deformation, Gap at Contacts
Lecture 33 - Application and Selection of Accumulators - Part I
Lecture 34 - Application and Selection of Accumulators - Part II
Lecture 35 - Hydraulic Circuits in Industrial Applications
Lecture 36 - Air preparation - Compressor and Accessories
Lecture 37 - Pneumatic Circuits
Lecture 38 - Analysis of Three - Way (Spool and Flapper Nozzle Valve)
Lecture 39 - Analysis of Flapper Nozzle Valves
Lecture 40 - Flow Force Compensation and Spool Design (Electro - hydraulic valves)
Lecture 41 - Premier and Guide to Oil - hydraulic fluids ; and Introduction to Fluid Power Symbols
Lecture 42 - Symbols in Oil Hydraulics
Lecture 43 - Appendices Tutorial on Basic Calculation on HST System and Hydraulic Fluids